设为荣鼎娱乐 设为收藏

联系方式

 

洛阳松导感应加热科技荣鼎娱乐 

联系方式:15038554363  

24小时技术热线:15038554363

电 话:0379—60125771

邮 箱:1390003299@qq。com

厂址:河南省洛阳市洛新工业园区

  • 产品
  • 5T中频熔炉

    中频熔炉

    中频感应炉

    250kg中频感应炉

    500kg中频感应炉

    1T中频感应炉

    2T中频感应炉

    5T中频感应炉

    3T中频感应炉

    400kW全自动中频感应加热炉

    棒料,圆钢中频感应加热设备

    中频钨钼烧结炉

    中频感应烧结炉

    钼丝钼块烧结炉

    钢管感应加热炉

    钢管感应加热炉

    Φ120mm圆钢感应加热炉

    350kW铝圆棒自动加热生产线

    Φ65mm圆钢中频锻造炉

    300KW中频感应加热设备

    300kw 中频锻造炉

    铜棒中频感应加热炉

    Φ70mm圆钢感应加热炉

    电机端环中频钎焊设备

    钻杆端中频加热设备

    3T 感应熔炼炉

    30t感应熔炼炉

    感应熔炼炉

    中频电炉维修
    分享到:
        本文为技术资料或者文章来自网络,仅供参考学习,如涉嫌侵权,请告知删除
        

    一种快速修复中频炉感应器铜管烧穿的工艺

    感应线圈打火严重时会将形成拉弧,严重的拉弧会导致铜管在拉弧部位被击穿。另一种情况是在炉衬被烧穿后,铁液外溢引起铜排烧穿。 铜排烧穿后造成冷却水外溢,必须立即停炉修复。由于铜排安装在炉壳内,焊补不便,修复时需拆卸取出。通常铜排修复工艺至少要浪费一个炉衬,还比较费时,下面就为大家介绍一种粘补法,为大家节约维修成本。 

    对第一种原因引起的铜排烧穿,可暂时停炉,同时将12mm厚的铜片剪成小块,其面积应稍大于铜排烧裂口面积,然后用锯片或手砂轮清除铜排烧穿处的残渣,并用砂纸打磨干净,迅速将FCR铜裂纹快速修补剂与固化剂混合,把修剪好的铜片在铜排烧裂处粘好,几分钟后FCR固化,即可形成很高的铜排粘结强度,此时就可以重新开炉了。

     对第二种原因引起的铜排烧穿,修复工艺过程如下:倾炉出铁→停炉→维修炉衬→铜排粘补→开炉。该修复工艺较传统的焊补修复也节省了一个炉衬及大量工时和烘炉电力。

    Process for quickly repairing copper tube burn-through of intermediate frequency furnace inductor

    When the induction coil is severely ignited, a arc will be formed, and a severe arc will cause the copper tube to be broken at the arcing portion. In another case, after the lining is burned through, the iron overflow causes the copper platoon to burn through.   After the copper platoon is burned, the cooling water overflows and must be immediately repaired. Since the copper bars are installed in the furnace shell, the welding repair is inconvenient and needs to be removed and removed during the repair. Usually, the copper platoon repair process wastes at least one lining, which is more time consuming. Here is a sticky method for everyone to save maintenance costs.  

    For the first reason caused by the copper row burn-through, the furnace can be temporarily shut down, and the copper piece of 1 ~ 2mm thick is cut into small pieces, the area should be slightly larger than the area of the copper discharge crack, and then removed by a saw blade or a hand grinding wheel. The residue of the copper platoon is burned and cleaned with sandpaper. The FCR copper crack fast repairing agent is quickly mixed with the curing agent, and the trimmed copper sheet is stuck in the copper row cracking. After a few minutes, the FCR is solidified. The high copper bond strength can be re-opened at this time.

      For the second reason caused by the copper row burn-through, the repair process is as follows: tilting the furnace iron → stopping the furnace → repairing the furnace lining → copper row bonding + opening furnace。 This repair process also saves a lining and a large amount of man-hours and oven power compared to conventional weld repairs。

     


    Copyright© 2007-2013洛阳松导感应加热科技荣鼎娱乐 All Rights Reserved 
    电 话:0379—60125771 手 机:15038554363
    网站正在制作中,随时修改,非正式运行。
    本站关键词:中频炉、中频电炉、熔炼炉
    智慧彩票投注 秒速时时彩 内蒙古11选5开奖 河北快3 智慧彩票投注 荣鼎娱乐 北京赛车 荣鼎娱乐 安徽快3 极速11选5

    智慧彩票投注 秒速时时彩 内蒙古11选5开奖 河北快3 智慧彩票投注 荣鼎娱乐 北京赛车 荣鼎娱乐 安徽快3 极速11选5