设为荣鼎娱乐 设为收藏

联系方式

 

洛阳松导感应加热科技荣鼎娱乐 

联系方式:15038554363  

24小时技术热线:15038554363

电 话:0379—60125771

邮 箱:1390003299@qq。com

厂址:河南省洛阳市洛新工业园区

  • 产品
  • 5T中频熔炉

    中频熔炉

    中频感应炉

    250kg中频感应炉

    500kg中频感应炉

    1T中频感应炉

    2T中频感应炉

    5T中频感应炉

    3T中频感应炉

    400kW全自动中频感应加热炉

    棒料,圆钢中频感应加热设备

    中频钨钼烧结炉

    中频感应烧结炉

    钼丝钼块烧结炉

    钢管感应加热炉

    钢管感应加热炉

    Φ120mm圆钢感应加热炉

    350kW铝圆棒自动加热生产线

    Φ65mm圆钢中频锻造炉

    300KW中频感应加热设备

    300kw 中频锻造炉

    铜棒中频感应加热炉

    Φ70mm圆钢感应加热炉

    电机端环中频钎焊设备

    钻杆端中频加热设备

    3T 感应熔炼炉

    30t感应熔炼炉

    感应熔炼炉

    电炉文章
    分享到:
        本文为技术资料或者文章来自网络,仅供参考学习,如涉嫌侵权,请告知删除
        

    1、设备类型:

    1吨塞棒底注式中频保温炉主要用于钢(铁)水的保温和提温,来自其它熔炼设备(如高炉、转炉、冲天炉)的钢(铁)水,倒入保温感应炉中,再微调成分,并适当提温至最终浇铸温度。

    设备主要技术参数

    A、综合参数

    序号

    项目

    参数要求

       1

    设备形式

    250kw

    2

    额定容量

    1T

    3

    最大容量

    1T+30%

    4

    工作温度

    1450铸铁保温

    5

    工作噪声

    <85分贝

    6

    炉体结构

    钢壳

    7

    出线方式

    侧出线

    B、电气参数:

    序号

    项目

    参数

    1

    电源功率

    250kw /361T

    2

    整流项数

    6

    3

    逆变器

    SCR并联逆变

    4

    额定频率              

    1000Hz

    5

    进线电压

    380V

    6

    直流电压

    500V

    7    

    中频电压  

    750V

    8

    启动成功率     

    100%

    9

    功率因数

    0.92

    C、冷却系统参数

    序号

    项目

    参数

    1

    闭环冷却塔

    ZXZ-N80T20/60)一体分层塔

    2

    冷却塔壳体

    镀铝锌板 或304不锈钢板

    3

    风机配套电机

    1。1KW

    4

    喷淋水泵

    2.2KW

    5

    循环泵

    7.5kw

    6

    冷却器

    304冷却器

    D、炉体指标

    序号

    项目

    参数

    1

    炉壳结构

    钢结构

    2

    磁轭材质

    Z11-0。23

    3

    磁轭覆盖率

    85%

    4

    磁轭夹紧

    不锈钢 1Cr18Ni9

    5

    磁轭散热方式

    双水冷

    6

    感应器铜管材质

    T2纯铜99.9

    感应圈内径

    900 壁厚5mm

    感应圈高度

    500mm

    7

    水路

    44

    8

    出线方式

    侧出

    9

    水冷圈材质

    紫铜管

    10

    炉壳发热量

    <75℃(炉底与炉盖除外)

    11

    绝缘

    线圈与磁轭绝缘采用云母板双层隔离

    12

    螺栓

    普通碳钢螺栓为8.8级。其他螺栓不锈钢材质或铜制

    13

    坩埚模厚度

    >5mm

    14

    水路连接软管

    采用无阻燃高绝缘橡胶管

    15

    集水器

    不锈钢材质

    炉体结构描述:

    5.1机械结构原理说明

    炉体采用钢壳磁轭炉体,金属熔液的出口通道“浇口”设在电炉底部。(高铝石墨质或氧化锆质水口)由于金属在熔炼过程中,杂质和熔渣均浮在液面;底注式浇注可避免杂质和熔渣进入铸件型腔,大大减少废品出现。 钢水出口连接有塞杆动作机构;塞杆动作机构包括塞棒、气缸和传动杠杆,塞棒底部形状与钢水出口形状相适配,且塞棒底部为由上至下渐缩形;气缸驱动传动杠杆沿一固定轴转动,传动杠杆带动塞棒作上升或下降动作。用塞杆动作机构的上升或下降运动来控制出钢口的开、关或开度,精确控制出钢点和出钢流量及出钢流速,

     

     

     


    塞杆动作机构包括塞棒2、气缸3和传动杠杆4,气缸3连接传动杠杆4的一端,气缸的底部固定;塞棒2连接传动杠杆4的另一端,塞棒2的底部形状与钢水出口形状相适配,且塞棒2的底部为由上至下渐缩形;气缸3驱动传动杠杆4沿一固定轴转动,传动杠杆4带动塞棒2作上升或下降动作。其特征在于钢水出口横截面为圆形,塞棒2的底部为圆椎形。传动杠杆4的另一端固定连接有悬挂套管5,悬挂套管5用于将塞棒2悬挂于传动杠杆4上。塞杆动作机构还包括旋转轴承6,旋转轴承6连接悬挂套管5和塞棒2之间。塞杆动作机构还包括支架7,支架7上固定连接有套筒型调正器(8);还包括缓冲弹簧10和位置固定杆9,悬挂套管5的下端与缓冲弹簧10的上端固连,缓冲弹簧(10)的

    1 ton stopper bottom injection type intermediate frequency holding furnace

    1 ton plug rod medium frequency holding furnace.cast tube special equipment

    I. Overview:

    1, equipment type:

    The 1 ton stopper bottom injection type intermediate frequency holding furnace

     is mainly used steel (iron) and raised temperature water insulation, steel (iron) melting water from other devices (such as blast furnace, converter, cupola), and poured into an induction furnace insulation, and then fine-tuning components, and provide appropriate Warm to the final casting temperature。

    Second , the main technical parameters of the equipment

    A, comprehensive parameters

    Serial number

    project

    Parameter requirement

       1

    Equipment form

    250kw

    2

    Rated Capacity

    1T

    3

    Maximum capacity

    1T +30%

    4

    Operating temperature

    1450 °C cast iron insulation

    5

    Working noise

    <85 decibels

    6

    Furnace structure

    Steel shell

    7

    Way out

    Side outlet

    B, electrical parameters:

    Serial number

    project

    parameter

    1

    Power supply

    250kw / 3 phase 6 pulse 1T

    2

    Number of rectifiers

    6 veins

    3

    Inverter

    SCR parallel inverter

    4

    Rated frequency

    1000 Hz

    5

    Line voltage

    380V

    6

    DC voltage

    500V

    7    

    IF voltage

    750 V

    8

    Start success rate

    100%

    9

    Power factor

    0.92

    C, with cooling system parameters

    Serial number

    project

    parameter

    1

    Closed loop cooling tower

    ZXZ-N 80 T ( 20/60) integrated layered tower

    2

    Cooling tower housing

    Galvanized or 304 stainless steel

    3

    Fan supporting motor

    1.1KW

    4

    Spray pump

    2.2 KW

    5

    Main circulation pump

    7.5kw

    6

    Cooler

    304 cooler

    D , furnace index

    Serial number

    project

    parameter

    1

    Furnace shell structure

    Steel structure

    2

    Yoke material

    Z11-0。 23

    3

    Yoke coverage

    8 5%

    4

    Yoke clamping

    Stainless steel 1Cr18Ni9

    5

    Yoke cooling method

    Double water cooling

    6

    Sensor copper tube material

    T2 pure copper 99。9

    Induction ring inner diameter

    900 wall thickness 5 mm

    Induction loop height

    500 mm

    7

    waterway

    4 in 4 out

    8

    Way out

    Side out

    9

    Water cooling ring material

    Copper tube

    10

    Furnace shell heat

    <75 ° C (except the furnace bottom and the furnace cover)

    11

    insulation

    The coil and the yoke are insulated by a double layer of mica board.

    12

    bolt

    Ordinary carbon steel bolts are grade 8。8。 Other bolts made of stainless steel or copper

    13

    Die thickness

    >5mm

    14

    Water connection hose

    Use non-flame retardant high insulation rubber tube

    15

    Water collector

    Stainless steel

    Fifth , the furnace structure description:

    5.1 mechanical principles described structure

    The furnace body adopts a steel shell yoke furnace body, and the outlet channel "gate" of the metal melt is arranged at the bottom of the electric furnace。 ( High-aluminum graphite or zirconia nozzle ) Since the metal is in the smelting process, impurities and slag float on the liquid surface; the bottom-injection casting can prevent impurities and slag from entering the casting cavity, greatly reducing the occurrence of waste。 The steel water outlet is connected with a plug rod action mechanism; the plug rod action mechanism comprises a plug rod, a cylinder and a transmission lever, the bottom shape of the plug rod is adapted to the shape of the molten steel outlet, and the bottom of the plug rod is tapered from top to bottom; the cylinder drive transmission The lever rotates along a fixed axis, and the transmission lever drives the plug to raise or lower。 Use the rising or falling movement of the plug rod action mechanism to control the opening, closing or opening of the taphole, and precisely control the tapping point and tapping flow rate and the tapping flow rate。

     

    The plug rod action mechanism comprises a stopper rod 2, a cylinder 3 and a transmission lever 4, the cylinder 3 is connected to one end of the transmission lever 4, and the bottom of the cylinder is fixed ; the stopper rod 2 isconnected to the other end of the transmission lever 4, the bottom shape of the stopper rod 2 and the molten steel outlet The shape is adapted, and the bottom of the stopper rod 2 is tapered from top to bottom; the cylinder 3 drives the transmission lever 4 to rotate along a fixed axis, and the transmission lever 4 drives the stopper rod 2 to ascend or descend. It is characterized in that the steel water outlet has a circular cross section, and the bottom of the stopper rod 2 has a circular cone shape. The other end of the transmission lever 4 is fixedly connected with a suspension sleeve 5 for suspending the stopper rod 2 from the transmission lever 4. The stopper action mechanism further includes a rotary bearing 6 that connects between the suspension sleeve 5 and the stopper rod 2. The plug action mechanism further includes a bracket 7 to which the sleeve type adjuster (8) is fixedly coupled; a buffer spring 10 and a position fixing rod 9 are further fixed, and the lower end of the suspension sleeve 5 is fixed to the upper end of the buffer spring 10 The lower end of the buffer spring (10) is fixed to the inner ring of the rotary bearing (6), and the outer ring of the rotary bearing 6 is connected to the position fixing rod (9) 


    Copyright© 2007-2013洛阳松导感应加热科技荣鼎娱乐 All Rights Reserved 
    电 话:0379—60125771 手 机:15038554363
    网站正在制作中,随时修改,非正式运行。
    本站关键词:中频炉、中频电炉、熔炼炉
    极速飞艇平台 山东11选5 澳洲幸运8 上海时时乐 67娱乐系统 北京两步彩 荣鼎娱乐 澳洲幸运10开奖结果 极速快乐8 上海时时乐

    极速飞艇平台 山东11选5 澳洲幸运8 上海时时乐 67娱乐系统 北京两步彩 荣鼎娱乐 澳洲幸运10开奖结果 极速快乐8 上海时时乐