设为荣鼎娱乐 设为收藏

联系方式

 

洛阳松导感应加热科技荣鼎娱乐 

联系方式:15038554363  

24小时技术热线:15038554363

电 话:0379—60125771

邮 箱:1390003299@qq.com

厂址:河南省洛阳市洛新工业园区

  • 产品
  • 5T中频熔炉

    中频熔炉

    中频感应炉

    250kg中频感应炉

    500kg中频感应炉

    1T中频感应炉

    2T中频感应炉

    5T中频感应炉

    3T中频感应炉

    400kW全自动中频感应加热炉

    棒料,圆钢中频感应加热设备

    中频钨钼烧结炉

    中频感应烧结炉

    钼丝钼块烧结炉

    钢管感应加热炉

    钢管感应加热炉

    Φ120mm圆钢感应加热炉

    350kW铝圆棒自动加热生产线

    Φ65mm圆钢中频锻造炉

    300KW中频感应加热设备

    300kw 中频锻造炉

    铜棒中频感应加热炉

    Φ70mm圆钢感应加热炉

    电机端环中频钎焊设备

    钻杆端中频加热设备

    3T 感应熔炼炉

    30t感应熔炼炉

    感应熔炼炉

    工业电炉技术资料
    分享到:
        本文为技术资料或者文章来自网络,仅供参考学习,如涉嫌侵权,请告知删除
        

    气动多触头内力压实造型机

    一,用途、特点

    本机可用于各种铸造车间粘土砂上下箱造型,可以单机使用或组成机械化流水线使用,亦可组成半自动线使用。

    本机3个特点

    1、采用气动多触头压实,没有漏油的困扰;比压适中,对型砂无特殊要求,触头数量多(60个),适合于复杂模型造型。

    2、本机在压实时,机架不受力,而是由多触头体侧面下垂四根拉杆钩住工作台,随着多触头的向下伸出,进行压实,如果把触头、钩子、砂箱、型板、工作台看成一个系统的话,这种压实力是内力或称内力压实。

    3、压震实,触头一方面压实砂型,同时随工作台一起震击(与机架脱离,机架不受震动)。故震击压实效果好,砂型硬度高而均匀(平均硬度达85~90,B型硬度计值),吃砂量可小至20~30毫米,吃砂比达H:B=2~3,且其型腔垂直面的硬度仍可达到80以上。

    本机采用弹簧全缓冲气动微震机构,故对地基无特殊要求,起模采用连杆

    同步轴结构,气压油调速,起模同步性好,速度控制自如。

    规格

    1.砂箱内尺寸             1520×1220(1320)×190mm

    2.砂箱最大外形尺寸       2100×1320×190mm

    3.工作台面尺寸           1980×1030mm

    4.正常工作气压           ≥0.55Mpa

    5.多触头数量               60只

    6.触头气缸内径             Ф100

    7.触头压头                  Ф118

    8.触头压实行程               250mm

    9。起模缸行程                 350mm

    10.起模缸直径               Ф160×2

    11。震击缸径                 Ф250

    12。压实缸径                 Ф600

    13。工作台至触头下平面距离    435mm

    14.砂箱型板总高度            350mm

    15.垫砂框至触头下面距离      20mm

    16.生产率                 35-40半箱/h

    17。总进气管(2处)          11/2  、 1”

    18.自由空气消耗量            3m3 /半型

    19。总质量                    6500kg

    Pneumatic multi-contact internal force compaction molding machine

    1, use, characteristics

    This machine can be used in the clay box of various casting workshops。 It can be used in a single machine or composed of a mechanized assembly line。 It can also be used as a semi-automatic line。

    This machine has 3 features:

    1. It adopts pneumatic multi-contact compaction and has no trouble of oil leakage. Compared with moderate pressure, there is no special requirement for molding sand, and the number of contacts is large (60), which is suitable for complex model modeling.

    2. The machine is pressed in real time, the frame is not force, but the four pull rods are hooked on the side of the multi-contact body, and the compaction is carried out as the multiple contacts protrude downward, if the contacts are , hooks, sand boxes, stencils, workbench as a system, this pressure is internal force or internal force compaction.

    3, compaction, the contact on the one hand compacted sand type, at the same time with the workbench together shock (disengaged from the frame, the frame is not subject to vibration)。 Therefore, the shock compaction effect is good, the sand hardness is high and uniform (average hardness is 85~90, B type hardness value), the amount of sand can be as small as 20~30 mm, and the sand ratio is up to H:B=2~3 And the hardness of the vertical surface of the cavity can still reach 80 or more。

    This machine adopts spring full cushioning pneumatic micro-shock mechanism, so there is no special requirement for foundation, and the connecting rod adopts connecting rod。

    Synchronous shaft structure, pneumatic oil speed regulation, good mold synchronization, and speed control.

    specification

    1. Inside the sandbox size 1520×1220(1320)×190mm

    2. The maximum size of the sand box 2100×1320×190mm

    3. Work surface size 1980×1030mm

    4。 Normal working pressure ≥0。55Mpa

    5. Number of multiple contacts 60

    6. Contact cylinder inner diameter Ф100

    7。 Contact head Ф118

    8. Contact compaction stroke 250mm

    9。 Draft cylinder stroke 350mm

    10. Drafting cylinder diameter Ф160×2

    11. Shock cylinder bore Ф250

    12。 Compaction cylinder diameter Ф600

    13。 The distance from the workbench to the lower surface of the contact is 435mm

    14. Total height of sand box type plate 350mm

    15. The distance between the sand frame and the contact is 20mm.

    16. Productivity 35-40 half boxes / h

    17. Total intake pipe (2 places) 11/2, 1”

    18. Free air consumption 3m3 / half type

    19. Total mass 6500kg


    Copyright© 2007-2013洛阳松导感应加热科技荣鼎娱乐 All Rights Reserved 
    电 话:0379—60125771 手 机:15038554363
    网站正在制作中,随时修改,非正式运行。
    本站关键词:中频炉、中频电炉、熔炼炉
    易中彩票开户 东方彩票 幸运赛车 安徽快3走势 159彩票app 上海时时乐开奖 北京两步彩 极速飞艇 三分PK拾平台 贵州快3计划

    易中彩票开户 东方彩票 幸运赛车 安徽快3走势 159彩票app 上海时时乐开奖 北京两步彩 极速飞艇 三分PK拾平台 贵州快3计划