设为荣鼎娱乐 设为收藏

联系方式

 

洛阳松导感应加热科技荣鼎娱乐 

联系方式:15038554363  

24小时技术热线:15038554363

电 话:0379—60125771

邮 箱:1390003299@qq。com

厂址:河南省洛阳市洛新工业园区

  • 产品
  • 0.5T 中频熔炉

    0.25T中频熔炉

    1T中频熔炉

    2T中频熔炉

    5T中频熔炉

    中频熔炉

    中频感应炉

    250kg中频感应炉

    500kg中频感应炉

    1T中频感应炉

    2T中频感应炉

    5T中频感应炉

    3T中频感应炉

    400kW全自动中频感应加热炉

    棒料,圆钢中频感应加热设备

    中频钨钼烧结炉

    中频感应烧结炉

    钼丝钼块烧结炉

    钢管感应加热炉

    钢管感应加热炉

    Φ120mm圆钢感应加热炉

    350kW铝圆棒自动加热生产线

    Φ65mm圆钢中频锻造炉

    300KW中频感应加热设备

    300kw 中频锻造炉

    铜棒中频感应加热炉

    Φ70mm圆钢感应加热炉

    电机端环中频钎焊设备

    中频电炉维修
    分享到:
        本文为技术资料或者文章来自网络,仅供参考学习,如涉嫌侵权,请告知删除
        

     

     

     

    中频炉逆变电路不能启动或启动困难的维修(英文版)

    ault phenomenon of induction melting furnace

    The inverter circuit of the IF power supply cannot be started or started up.

    Fault analysis and processing

    The main reason why the inverter circuit of the IF power supply cannot be started or started is as follows.

        (1) Short circuit between induction coils. If the induction coil does not cool well for a long time, the insulation is broken and a short circuit between turns is caused. Conductive materials such as dust and scale on the induction coil can also cause short-circuit between turns. When the intermediate frequency power supply is started, the ignition phenomenon occurs, and frequent ignition may cause the induction coil to break down. In this case, the surface of the induction coil should be cleaned, brushed with insulating paint or asbestos board.

        (2) The induction coil is short-circuited to the arc furnace casing。 The induction coil housing is loose and there is too much ash in the furnace; the induction coil is discharged through the furnace base。 In this case, the induction coil should be reinforced to remove dust。

        (3) The copper busbar connected to the induction coil at the intermediate frequency output is short-circuited。 If there is a foreign object or the copper is not fixed, it may cause a short circuit between the copper rows。

        (4) The capacitor case is short-circuited to the ground. At this time, it should be checked whether there is water leakage, whether the capacitor base is too dusty, and whether the ceramic base of the capacitor is missing.

        (5) The water-cooled cable is disconnected, and the copper bus that is output to the load is blown.

        (6) Check if the current transformer insulation is damaged; remove the current transformer to check whether the insulation is good; use a multimeter to measure whether the coil is blown, and check if the wiring sequence is correct. If both are normal, check whether the potentiometer of the current signal adjustment is too small. The amplitude of the output current signal should be re-adjusted.

    (7) Check if the inverter circuit's inverter angle is too small. If it is too small, adjust the inverter angle; if it is normal, check if the current polarity is reversed. If not, check the inverter thyristor for a trigger pulse. If it is normal, check the inverter thyristor for damage. If it is damaged, replace it with a thyristor of the same type and specification.

     


    Copyright© 2007-2013洛阳松导感应加热科技荣鼎娱乐 All Rights Reserved 
    电 话:0379—60125771 手 机:15038554363
    网站正在制作中,随时修改,非正式运行。
    本站关键词:中频炉、中频电炉、熔炼炉
    秒速时时彩 北京幸运28 159彩票 极速快乐8 极速飞艇 一分时时彩 三分时时彩 上海11选5 吉林快3 极速PK拾

    秒速时时彩 北京幸运28 159彩票 极速快乐8 极速飞艇 一分时时彩 三分时时彩 上海11选5 吉林快3 极速PK拾